Default Category Archives

2-axis CPM-IP I/O Hub with Motor I/O

Monday, November 24th, 2025

Easily connect up to two CPM-IP motors and their motor-related I/O to an EtherNet/IP Scanner. Built-in IP-Sync technology enables sub 200-nanosecond synchronization. See the CPM-IP User Manual for more information on IO-HUB-2-R’s functionality.

Posted in | Comments Off on 2-axis CPM-IP I/O Hub with Motor I/O

225 Watt DC Power Supply

Wednesday, March 2nd, 2016

Low Voltage (75 VDC) “Intelligent Power Center” power supply optimized for motor drive bus power. Compatible with ClearPath NEMA 23 and 34 integrated servos, and Eclipse and Meridian 2xx-5xx series products.

Posted in | Comments Off on 225 Watt DC Power Supply

24 VDC Power Supply

Friday, June 19th, 2020

156 watt DC power supply capable of powering a ClearCore with a full complement of I/O devices, with extra power to spare for expansion I/O.

Protection: Short circuit / Overload / Over-voltage / Over-temperature. Compliance with UL62368-1, EN61558-1/2-16. Operating temperature -25 to 50 deg. C with no derating.

Posted in | Comments Off on 24 VDC Power Supply

24 Volt Power, 2-Pin Molex Cable

Wednesday, August 10th, 2016

Cable used to supply 24 volt logic power to a number of ClearPath devices (e.g., SC4-HUB power, daisy-chained power from SC4-HUB to SC4-HUB, ASU-FR510, power from POWER4-HUB to SC4-HUB, etc.) Can be cut in half to make two shorter cables with flying leads.

Posted in | Comments Off on 24 Volt Power, 2-Pin Molex Cable

3 Amp DC Power Supply

Wednesday, March 20th, 2013

The E3PS12-75 is the ideal power supply to drive 2 to 5 ClearPath motors (application dependent: low motor power usage will increase the number of motors that can be driven off of one supply). The supply has selectable AC input voltage, and a multi-position switch to adjust the output for high and low AC line voltages so that you always get the most power from your motors. The E3PS12-75 also has built-in controls to handle regenerated energy from the motors to minimize over-voltage conditions when decelerating quickly or driving vertical loads. See DC Power Supplies for more details.

Posted in | Comments Off on 3 Amp DC Power Supply

350/500 Watt DC Power Supply

Wednesday, March 2nd, 2016

Posted in | Comments Off on 350/500 Watt DC Power Supply

4-axis CPM-IP I/O Hub with Enhanced I/O

Monday, November 24th, 2025

Easily connect up to four CPM-IP motors, and general purpose I/O to an EtherNet/IP Scanner. Built-in IP-Sync technology enables sub 200-nanosecond synchronization. See the CPM-IP User Manual for more information on IO-HUB-4-E’s functionality.

Posted in | Comments Off on 4-axis CPM-IP I/O Hub with Enhanced I/O

4-axis CPM-IP I/O Hub with Motor I/O

Monday, November 24th, 2025

Easily connect up to four CPM-IP motors and their motor-related I/O to an EtherNet/IP Scanner. Built-in IP-Sync technology enables sub 200-nanosecond synchronization. See the CPM-IP User Manual for more information on IO-HUB-4-R’s functionality.

Posted in | Comments Off on 4-axis CPM-IP I/O Hub with Motor I/O

6 Inch Ribbon Cable

Friday, April 9th, 2021

Ribbon cable for ClearCore/ClearLink Encoder Input adapter (CL-ENCDR-DFIN).

Posted in | Comments Off on 6 Inch Ribbon Cable

AC Power Cable for E3PS12-75

Wednesday, March 20th, 2013

AC line cord for the E3PS12-75 DC Power Supply. Plugs into standard 120V AC (nominal) U.S. wall socket. Length of cable is 1.98 m (6.5 ft).

Posted in | Comments Off on AC Power Cable for E3PS12-75

AC Power Cable for IPC-3 and IPC-5

Wednesday, March 2nd, 2016

AC Power (120VAC) Cable for IPC-3 and IPC-5 motor drive power supplies.

Posted in | Comments Off on AC Power Cable for IPC-3 and IPC-5

Analog Send Unit

Wednesday, March 2nd, 2016

Need to use analog control signals? For maximum noise immunity, ClearPath-MC natively uses digital control signals, but this “Analog Send Unit” (ASU) allows you to use analog control signals (0-10V or 4-20mA) while minimizing associated noise issues. The ASU converts analog signals to digital signals compatible with ClearPath-MC, so you won’t have noise corruption. Just locate the ASU as close as possible to your analog source and send the accurately converted digital signals to ClearPath’s optically isolated inputs for high-fidelity control.

Posted in | Comments Off on Analog Send Unit

Atmel-ICE Debugger

Friday, June 19th, 2020

Atmel-ICE development tool for debugging software on ARM Cortex-M devices such as ClearCore. Requires cable p/n TC2030-CTX-LEMTA for use with ClearCore. Powered via USB.

Posted in | Comments Off on Atmel-ICE Debugger

Blower Kit

Friday, August 25th, 2017

This blower kit (AC powered fan and shroud) provides a significant increase in continuous torque for certain AC-input (integral hp) ClearPath motors. Motor part numbers shown with a “_fan” after them show the increased specifications using this blower. Note that this kit is not IP rated for dust or liquid protection, and needs AC wiring separate from the motor. For wiring and installation instructions, refer to the user manual: AC Input, Integral Horsepower ClearPath Motors.

Posted in | Comments Off on Blower Kit

Cable, Atmel-ICE to ClearCore

Friday, June 19th, 2020

Required for use with ClearCore

Posted in | Comments Off on Cable, Atmel-ICE to ClearCore

Cat5e Patch Cable

Friday, June 19th, 2020

Cat5e cable used to connect CCIO-8 expansion I/O modules to ClearCore. Flexible, snag-free, cable boot protects the plug while making it easy to depress the locking clip. 24AWG stranded, pure bare copper conductors. 50μm gold-plated contacts.

One cable required per CCIO-8.

Posted in | Comments Off on Cat5e Patch Cable