Teknic homepage

ClearPath® - Integrated Servo System

CPM-MCVC-D1004P-RLN

The ClearPath-MCVC model is used mainly for velocity (speed) control replacing AC induction motors, synchronous motors, DC motors, and more expensive (and non-integrated) servo systems. But it also has a torque mode, as well as the ability to precisely move between two different user-defined positions, so it can replace pneumatic and hydraulic cylinders. In all cases, you get smooth, quiet, bi-directional, and precisely servo-regulated motion in a low-cost, integrated package.

Operating Modes

Ramp to Selected SpeedBy changing digital inputs (from your PLC, switches, etc.), ClearPath will smoothly ramp to one of four preset speeds.
Manual Speed ControlFine control of speed from zero to max speed at the turn of a knob. Remembers your last set speed or resets to zero speed when motor is enabled.
Spin on Power UpJust turn on power and smoothly ramp to your preset speed. For when all you need is reliable, constant speed from a brushless motor, and a bare minimum of wiring. It doesn't get any easier than this.
Variable SpeedConnect a digital waveform (PWM or frequency) from your PLC or other device, and ClearPath will run at a speed proportional to the waveform. (This mode can also be used to make ClearPath a drop-in replacement for a brush motor.)
Variable TorqueApply a variable torque (or force or tension) in proportion to a digital command (PWM or frequency)
Sensor PositioningTrigger ClearPath to move in either direction and it will smoothly ramp up to a chosen speed and stop when it detects a sensor (or switch).
Absolute PositioningTrigger ClearPath to move to one of two preset positions. Perfect for replacing air cylinders where more power and finesse is needed.

Torque/Speed Curves

Peak Torque

 

Cont. (RMS) Torque
at 30°C

 

Speed (RPM)
Torque (oz-in)
Torque (N-m)
Peak Torque
Cont. (RMS) Torque
Max Speed
Peak Power
Cont. (RMS) Power

Purchase

Qty 1-9Qty 10-49Qty 50-99Qty 100-199Qty 200+
$698 Volume pricing requires registration

Accessories

Click the "See Accessories" button to view a list of required and recommended accessories to complete your ClearPath system. Select from assorted cables and more. Also, download your free copy of ClearPath software.

Specifications

Motor Frame SizeIEC D100* - 7.09 in (180.09 mm) sq.
Length9.15 in (232.41 mm)
Input Voltage Range
Input Voltage for 5-wire systems
100-240 VAC (1- or 3-phase)
300-415 VAC (3-phase, 5-wire)
Peak Torque (@230 VAC 3-ph)1,985 oz-in (14.0 N-m)
Cont. (RMS) Torque (@230 VAC 3-ph)1,147 oz-in (8.1 N-m)
Max Speed (@230 VAC 3-ph)2820 RPM
Achievable Resolution 0.090 degrees
Repeatability 0.006 degrees
Shaft Diameter 1.103 in (28.00 mm)
Weight26.3 lb (11.9 kg)
Rotor Inertia104.9 oz-in² (19.2 kg-cm²)
Logic Input Voltage Range4.0 to 28 VDC
Maximum Radial Load 170 lbf (756.2 N)
Maximum Thrust Load40 lbf (177.9 N) in; 70 lbf (311.4 N) out
Ambient Temperature2-40° to +70° C
Ambient Humidity0-95%; non-condensing
Environmental Rating3IP65
Regulatory CertificationsUL Listed for use up to 240 VAC;
CE certified for use up to 415 VAC; RoHS
Country of OriginUSA
Warranty3 Years

2The RMS torque limit on certain motors is derated for operation in ambient temperatures above +40 degrees C. Contact Teknic for derating assistance.

3Order the shaft seal option if you want the IP-65 rating to cover the front mounting face of the motor in addition to the body.

Motion & I/O Controllers Compatible with ClearPath Servos

Control your ClearPath-MC servo systems with a ClearCore or ClearLink Motion & I/O Controller. ClearCore is a C++ programmable controller for general-purpose machine control, while ClearLink adds motion and I/O capability to any EtherNet/IP-compatible PLC.

With either controller you can coordinate up to four ClearPath-MC motors per controller. You can also control 13 software-configurable, analog and digital I/O points (up to 24VDC). Both controllers can be networked to control larger systems with more motors, and you can use I/O expansion modules to increase the I/O count.

ClearCore — C++ Programmable Controller
ClearCore C++ programmable controller
  • Rich C++ library with dozens of example programs
  • Multiple communications (serial, wireless, etc.)
Learn More
ClearLink — EtherNet/IP Controller
ClearLink EtherNet/IP controller
  • Works with any EtherNet/IP-compatible PLC
  • Powerful EDS file reduces development time
Learn More

AC Blower Kit

Blower Kit

Blower Kit
Part Number: BLOWER-1P230V
Connector: Screw Terminal Block
Length: Adds 2.12 in to motor length (see manual/3D models for specifics)
Input Power: Single-phase 190-230 VAC
Weight: 2.0 lbs

This blower kit (AC powered fan and shroud) provides a significant increase in continuous torque for certain AC-input (integral hp) ClearPath motors. Motor part numbers shown with a “_fan” after them show the increased specifications using this blower. Note that this kit is not IP rated for dust or liquid protection, and needs AC wiring separate from the motor. For wiring and installation instructions, refer to the user manual: AC Input, Integral Horsepower ClearPath Motors
Qty 1-9Qty 10-49Qty 50-99Qty 100-199Qty 200+
$57$56$55$54CONTACT